spacer


3" and 4" Leaf Eater Advanced Rain Head

3" and 4" Leaf Eater Advanced Rain Head

Price: $29.99  
Part Number: RH-RHAD100  
Weight: 3 lbs.  
Ships From: CA  
USD Shipping: Calculate Shipping  
PDF Drawing: View Technical Drawing  
Manufacturer: Rain Harvesting  
Contact Us  
Need this to ship right away?
3" and 4" Leaf Eater Advanced Rain Head - Dripping Springs, TX
3" and 4" Leaf Eater Advanced Rain Head - Channelview, TX
3" and 4" Leaf Eater Advanced Rain Head - San Antonio, TX
  • 3" and 4" Leaf Eater Advanced Rain Head
  • 3" and 4" Leaf Eater Advanced Rain Head
  • 3" and 4" Leaf Eater Advanced Rain Head

Leaf Eater Advanced

The Leaf Eater Advanced™ is the next generation Rain Head, featuring the new Clean Shield™ (single screen) technology and VH Pivot™ outlet. The Leaf Eater Advanced™ Rain Head prevents debris from entering the Rain Harvesting system, improves water quality and reduces tank/cistern maintenance.

The single screen incorporates Clean Shield™ technology which deflects leaves and debris away from the flow of water. This minimises maintenance and enhances catchment efficiency. This Rain Head incorporates a VH Pivot™ outlet that swivels to suit vertical or horizontal downspouts. The Leaf Eater Advanced™ can also be used as a debris removing device even when rainwater is not being collected.

Features and Benefits
Compact, versatile rain head for quick and easy installation
Single screen technology for advanced debris shedding (Clean Shield™)
Minimal maintenance
Pivot the outlet to suit vertical or horizontal (rear outlet) downspouts (VH Pivot™)
High flow rate performance
Superior catchment efficiency at low and high flow rates
Single screen with 1/32" aperture mosquito proof stainless steel mesh
Include adaptor for secure connection to downspout

New and improved version comes with adapters that can be used for 3" or 4" option.
The 3" and 4" Leaf Eater Advanced Rain Heads (RHAD99 and RHAD98) have been replaced by the dual size Leaf Eater Rain Head (RHAD100), ideal for either 3" or 4" application.

Installation Instructions

Gutter & Mid-Mount Installation

  1. Gutter: Measure 10½” from the bottom of the existing gutter pop and remove this section of downspout. Ensure the cut edge is clean and smooth. Mid-Mount: Remove 10½” of downspout where the Leaf Eater Advanced™ is to be situated. Ensure all cut edges are clean and smooth. (figure 1)
  2. Using the quick release tabs remove the Clean Shield™ screen bylifting it up and then out. (figure 2)
  3. Insert the Leaf Eater Advanced™ by sliding it up over the cut section and then down into position. The Leaf Eater Advanced™ outlet should be slid firmly onto the bottom down pipe until it can be pushed no further. (figure 3)
  4. Screw the Leaf Eater Advanced™ into position through the screw slots provided. Ensure appropriate screws and anchors (if required) are used. (figure 5)
  5. Insert the Clean Shield™ screen into the Leaf Eater Advanced™. Ensure the Clean Shield™ screen is sitting firmly in place and check installation is secure. (figure 6).
Leaf Eater Advanced Installation

Horizontal (Rear Outlet) Installation

  1. Using the quick release tabs remove the Clean Shield™ screen by lifting it up and then out. (Figure 2)
  2. Swivel the outlet to the horizontal position – some force may be required.
  3. Position the Leaf Eater Advanced™ next to existing pipework, mark and cut top and bottom cut lines as per figure 4 . Ensure the cut edge is clean and smooth.
  4. Insert the Leaf Eater Advanced™ by sliding the rear outlet into the horizontal pipe. The back fixing plate must sit behind the top section of downspout. (figure 3)
  5. Screw the Leaf Eater Advanced™ into position through the screw slots provided. Ensure appropriate screws and anchors (if required) are used. (figure 5)
  6. Insert the Clean Shield™ screen into the Leaf Eater Advanced™. Ensure the Clean Shield™ screen is sitting firmly in place and check installation is secure. (figure 6)


live chat support button

 

made in the usa